Drive is busy example, not solution: drive ST3500320AS SD15
remove 3 screws nearest heads connector, motor connected, put something between pcb and hda to lift pcb and prevent contact.
power on, wait until drive stops motor
(ctrl+z)
F3 T>/2
F3 2>Z
Spin Down Complete
Elapsed Time 0.146 msecs
F3 2>U
Spin Up Complete
Elapsed Time 6.864 secs
this part is not necessary, use when first try fails
F3 2>/
F3 T>F712
Byte:0712: RealTimeUpdatedFlags = 00 00
Byte:0712: Bit:0, HPA_SET_BY_SETMAX = 0
Byte:0712: Bit:1, HPA_SET_BY_SETMAX_EXT = 0
Byte:0712: Bit:2, DCO_SET_ACTIVE = 0
Byte:0712: Bit:3, CONGEN_READ_FROM_MEDIA = 0 <- configuration not loaded from surface
F3 T>F,,22
Drive Configuration restored to defaults.
F3 T>F712
Byte:0712: RealTimeUpdatedFlags = 08 00
Byte:0712: Bit:0, HPA_SET_BY_SETMAX = 0
Byte:0712: Bit:1, HPA_SET_BY_SETMAX_EXT = 0
Byte:0712: Bit:2, DCO_SET_ACTIVE = 0
Byte:0712: Bit:3, CONGEN_READ_FROM_MEDIA = 1 <- done
(end of part to skip at first attempt)
F3 T>/1
F3 1>N1
F3 1>/
F3 T>m0,2,2,0,0,0,0,22
Max Wr Retries = 00, Max Rd Retries = 00, Max ECC T-Level = 00, Max Certify Rewrite Retries = 0000
User Partition Format 5% complete, Zone 00, Pass 00, LBA 00008DED, ErrCode 00000080, Elapsed Time 0 mins 05 secs
User Partition Format Successful - Elapsed Time 0 mins 05 secs
F3 T>
(finished, power off)
Atau :
Drive is busy example, not solution: drive ST3500320AS SD15
remove 3 screws nearest heads connector, motor connected, put something between pcb and hda to lift pcb and prevent contact.
power on, wait until drive stops motor, if you dont wait at this moment you got 000000CE error after next command
(ctrl+z)
F3 T>/2
F3 2>Z
Spin Down Complete
Elapsed Time 0.146 msecs
remove isolation and mount pcb as normal
F3 2>U
Spin Up Complete
Elapsed Time 6.864 secs
Quote
this part is not necessary, just checking is everything ok, use when first try fails (F712 work only on 500g 7200.11 with firmware SD15, when you updated f/w just skip this part
F3 2>/
F3 T>F712
Byte:0712: RealTimeUpdatedFlags = 00 00
Byte:0712: Bit:0, HPA_SET_BY_SETMAX = 0
Byte:0712: Bit:1, HPA_SET_BY_SETMAX_EXT = 0
Byte:0712: Bit:2, DCO_SET_ACTIVE = 0
Byte:0712: Bit:3, CONGEN_READ_FROM_MEDIA = 0 <- configuration not loaded from surface
F3 T>F,,22
Drive Configuration restored to defaults.
F3 T>F712
Byte:0712: RealTimeUpdatedFlags = 08 00
Byte:0712: Bit:0, HPA_SET_BY_SETMAX = 0
Byte:0712: Bit:1, HPA_SET_BY_SETMAX_EXT = 0
Byte:0712: Bit:2, DCO_SET_ACTIVE = 0
Byte:0712: Bit:3, CONGEN_READ_FROM_MEDIA = 1 <- done
F3 2>/
F3 T>F712
Byte:0712: RealTimeUpdatedFlags = 00 00
Byte:0712: Bit:0, HPA_SET_BY_SETMAX = 0
Byte:0712: Bit:1, HPA_SET_BY_SETMAX_EXT = 0
Byte:0712: Bit:2, DCO_SET_ACTIVE = 0
Byte:0712: Bit:3, CONGEN_READ_FROM_MEDIA = 0 <- configuration not loaded from surface
F3 T>F,,22
Drive Configuration restored to defaults.
F3 T>F712
Byte:0712: RealTimeUpdatedFlags = 08 00
Byte:0712: Bit:0, HPA_SET_BY_SETMAX = 0
Byte:0712: Bit:1, HPA_SET_BY_SETMAX_EXT = 0
Byte:0712: Bit:2, DCO_SET_ACTIVE = 0
Byte:0712: Bit:3, CONGEN_READ_FROM_MEDIA = 1 <- done
F3 T3>/1
F3 1>N1
F3 1>/
F3 T>m0,2,2,0,0,0,0,22
Max Wr Retries = 00, Max Rd Retries = 00, Max ECC T-Level = 00, Max Certify Rewrite Retries = 0000
User Partition Format 5% complete, Zone 00, Pass 00, LBA 00008DED, ErrCode 00000080, Elapsed Time 0 mins 05 secs
User Partition Format Successful - Elapsed Time 0 mins 05 secs
F3 T>
(finished, power off, connect disk to pc and check your data)
Agan-agan juga dapat Check Video Youtubenya di : http://www.youtube.com/watch?v=29FztWJVxbM
Sumber : http://www.msfn.org/board/topic/128807-the-solution-for-seagate-720011-hdds/page__st__520__p__832876
